wear resistant ceramic adhesiv > ceramic tile adhesives

ceramic tile adhesives

Ceramic tile adhesives,ceramic installation bonding agent,wear resistant tile adhesive:

Performance feature：
1. It’s the two component adhesive compounded by modified toughening resin and special curing agent.
2. Aging resistant,with good water resistance,good toughness and high strength.
3. Can cure at room temperature,can also heat for curing.
4.With strong initial adhesion,it will not flow and fall off without using magnet or other support measures
during ceiling and facade construction,it is suitable for ceiling and facade construction.

Product usage：
Used in the bonding of wear resistant ceramic chip on the top surface and facade of the equipment.With strong initial adhesion,it won't fall
off without using magnet or other support measures during ceiling and facade construction,optimizing construction technology and reducing construction cost.

Performance index：

Product name	physical state	Standard packing	operation time limit (25℃)	Curing time (25℃)	Range of application
Ceramic tile epoxy adhesive	paste	5 kg/set	0.5h	12 hours	Used in the self-adhesion and each-adhesion between metal and ceramic etc materials.Especially used in the bonding of wear resistant ceramic chip on the ceiling and facade of the equipment which suffers ash powder scour and material scour or erosive wear.

Item model	Color	Density (g/cm³)	Shear strength (Mpa) GB7124-2008	Impact strength (J/cm²) GB6328-1999	Tensile strength (Mpa) GB6329-2008	Compressive strength (Mpa) GB1041-2008	Working temperature （℃）
BD121	white	1.24	15	56	78	92	-60-150

How to use:
1. Surface treatment: Clean up the dust,greasy dirt and rust on the surface of adherend,then grind or sand blast treatment,finally clean it by
cleaning agent and dry it by airing.

2.Configure adhesive: According to the specified requirement,make A and B components mix uniformly,the mass ratio A:B=4:1. When the
temperature is low in winter,can preheat the A component up to the temperature of 40-50℃ in advance for easy to mix using.

3.Using adhesive: Make the configured adhesive be coating on the adherend surface uniformly,then fold it,knock on it for once from the middle
to all around with rubber hammer,avoid the air getting into it.Double spread will get the better effect,under the premise of no shortage adhesive,the adhesive layers are the thinner the better.

4.Curing: Room temperature initial curing for 4 hours,full curing for 24 hours,when the temperature is low in winter,can heat it up to the
temperature of 80℃ slowly and keep this temperature for 2 hours after placing it for 2 hours.

Packing specification:
Packed in a plastic drum, A component: 4Kg/drum, B component: 1Kg/drum,12 drums/carton or 8 drums/carton.

Transportation storage:
Sealed storage in the cool and dry place.The warranty period is 1 year.Avoid placing it upside down,knocking against and transporting it as a
non-dangerous product during transportation.

Special version:
1.This parameter is for laboratory conditions,due to the actual working condition is more complex,suggest the users to do the pretest
according to actual working condition

2.When the environment temperature is below 15℃,the curing time will prolong,should take proper heating measure.

3.When the environment temperature is more than 25℃ or the mixing quantity is too large,the curing speed will expedite,should properly
shorten the application time of coating after mixing.

Construction protective measures：
1.Wear the protective masks,wear the protective glasses and rubber gloves
2.Need washing hands with soap before eating,drinking or smoking.
3.The health hazard after touching: a few people will have skin allergy phenomenon,see a doctor in time and avoid touching with this product again.should wipe it with ethyl acetate when the sizing material paste on the skin by careless,then wash it with clear water.Should wash it
with clear water immediately and see a doctor when splashing into the eyes by careless.

Warm Prompt：
Residual adhesive solution cured products are non-toxic harmless organic solid,but maybe it will produce poisonous gas when burning,non-professional personnel can not do combustion disposal,should be sent to garbage power plant or garbage burning place treatment.

fire prevention measures：
Should choose dry powder to extinguish fire,can cover and flap it with dry powder,grit(the construction using abrasive) or the non chemical
fiber fabric when the sizing material catching fire.

Product packaging photo of our BD121 ceramic tile adhesives,ceramic installation bonding agent.

------分隔线----------------------------